Chickadee Twilight Lantern

Chickadee Twilight Lantern

• These tea lanterns add ambiance to any evening. Fill with a 3 inch candle.
• Dimensions: 9.5"L x 9.5"W x 9.5"H
• Rests on Surface or Hangs on Hook.
• Available in 3 finishes: Oil Rub Bronze, Copper Verdi or French Bronze

The Z-Counter admix is designed to just add to a normal 60lb bag of (concrete mix from your hardware store).

The Admix package is a multi-component blend of precicely measured cements and proprietary materials.

The Admix will also make finishing the concrete easier, reduce set times, and significantly higher strength.

It is common to take a normal 60lb bag of concrete that has a strength rating 3,000-3,500 psi, and get 7,500-8,000 psi just from adding this Admix to it.

Yield: One 8lb Admix package mixed with one 60lb bag of concrete will yield approx. 3.75 square feet at 1.5" thickness.

Chopped Fibers (sold here) can also be added to give additional strength and crack resistance.

Voids and pinholes in the finished concrete surface can be filled with a Slurry Mix (sold here).

Sold as a single pack, or in a 6-Pack.

View the Technical Data Sheet.

Concrete Countertop Cast In Place Forms- Quarter Bulnose

Cast-in-Place Concrete Countertop Forms, Z-Counterforms.

Profile Design: Quarter Bulnose.  Other Profiles Available- click here to see all designs.

Creates a 2 1/4" height edge to the in-place concrete countertop.

Each box includes 8x 8' Countertop Forms (96 lineal feet), and 6x 8' Back-Wall pieces (48 lineal feet).

Easy to set up and use, for both professional and DIY.

• The Quarter Bulnose edge will create a tiny small lip at the top of the concrete, due to the thickness of the plastic form itself.  If this is not desired, either polishing the finished concrete surface to remove it, or troweling the concrete surface down to just under the height of the countertop edge will remove the lip.
  

Application:

• These Countertop Forms are designed to be attached to the cement board, which is screwed onto the top of the cabinets.  The Countertop Forms are simply snapped off when the concrete is cured, leaving behind the decorative edge countertop surface.
• Please watch the video below for a quick demonstration how to use the Forms:
  
• Step 1: Attach cement board (1/2" thickness size, from your local hardware store) to the top of the cabinetry.
• Step 2: Cut the Countertop Forms with a miter saw, and screw in place onto cement board.  Use plenty of screws to ensure the Forms stay in place and can't move when you snap off the form later (once the concrete is cured). Tape the outside of each joint with duct tape to ensure a tight, waterproof joint.
• Using the Edge Expert (sold here) makes cutting angles on the Forms on a miter saw safe and easy.
• Step 3: Place Back-Wall pieces across the back of the countertop area (6 Back-Wall pieces (8' long each) are included with each box of Countertop Forms.  Back-Wall pieces have an 'L' shape to them, and can be screwed down to the cement board.  They create a back edge to allow a screed to be run across the concrete, creating a smooth, flat countertop.
  
• Step 4: OPTIONAL- Cut a 2 5/8" hole in the cement board for each faucet hole needed, and insert the Cast-in-Place Faucet Knockouts (sold here in a 2-pack) into the hole.
• Step 5: OPTIONAL- Create a hole for a sink, if needed. 
  
• For an under-mount style sink, cut a hole in the cement board to fit the sink into, use the Cast-in-Place Sink Form (sold here) to attach to the sink itself, and place the sink into the cement board. 
• For a drop-in style sinks or cook top stove drop-ins, the Back-Wall Pieces can be used to create a square or rectangular area.  Styrofoam can also be used to create a knockout of any size or shape needed.
• Step 6: Silicone all areas of the form where water could leak out.  This includes along the inside edge where the Forms are screwed to the cement board, along the back wall, across joints in the cement board, and around any sink knockouts.
• Step 7: Fill form with concrete.  Pack the concrete into the Edge Form to remove any large air pockets, and vibrate the Edge Form with a palm sander or other vibration source.  Poor vibration will result in a large number of voids in the concrete edge- ranging from small pinholes to larger pea sized holes.  Sometimes this look is sought after, but if it's not, make sure to vibrate well.
• A long enough trowel is the key to a flat countertop.  We recommend a 16" Magnesium Float (sold here) for basic needs, and either a 30" Darby Float (sold here) or 42" Darby Float (sold here) depending on your countertop depth.  A 16" Steel Trowel (sold here) is good to finish the concrete once it sets up for a smooth finish.
  
• Step 8: Allow concrete to cure (usually a few days).  Remove and tape from the joints.   Sand off any excess concrete from the top corners (where concrete meets the Countertop Forms) with a Diamond Sanding Foam Pad (sold here) or a Flexible Diamond Sanding Strip (sold here).
  
• Step 9: Remove Countertop Forms by simply pulling them away from the concrete, which will snap the Edge Form off, leaving the concrete countertop.
• Step 10: OPTIONAL- Polish concrete using diamond polishing pads.  Cast-in-Place concrete will usually have some unevenness to it, which can be lightly polished off using Dry Polishing Pads (sold here), usually grits 50,100,200 is sufficient.  If polishing down to expose more aggregate, consider using Wet Polishing Pads (sold here).
• Step 11: Any surface or edge pinholes and voids in the concrete can be filled with a Cement Slurry (sold here).
  
• Steps 12,13,14... Concrete can be stained (stains sold here) if desired.  Concrete Countertop Sealers can be applied once the concrete is dry (sealers sold here).  

Shockwave™ Power Screed - Power Unit Only

Shockwave™ Power Screed - Power Unit Only

• Excellent Vibration dampening (little vibration passed on to operator)
• Fully adjustable handlebars and grips
• Power trowel style throttle lever - does not require constant contact
• Reliable Honda® 4-stroke engine
• Direct drive shaft for extended life
• On board tachometer/hour meter great for rental and scheduled maintenance
• Easy to adjust eccentric weights that are completely protected from concrete splatter
• Accessible handles for easy lifting and transport
• Unique frame provides superior engine protection
• Don't forget blades!

Concrete Grout Slurry and Acid Stain Gloves

Durable concrete fabrication gloves.

Ideal for working with concrete, applying grout or slurry, and working with acid stain.

Gloves are pliable, but tough.

Long wearing with a non-slip textured surface in the hand area.

Flock lined for easy on/off.

14" long.